BPR in ICT: Finding Balance Between Two Fair Value Gaps

BPR in ICT (Balanced Price Range) is the overlap between two opposing fair value gaps. Rather than treating one FVG as an automatic magnet, a BPR shows where two imbalances have partially balanced. This guide focuses on marking both source FVGs, reading premium/discount and planning entries with defined risk.

Example status: The prices, timestamps and tick-volume figures below are hypothetical teaching inputs, not verified historical market data or backtest results.

Which two FVGs create a BPR?

Mark the first FVG created by a displacement. When an opposing impulse creates a second FVG and the two boxes intersect, the intersection is the BPR. Its boundaries come from the actual overlap, not a discretionary extension. A BPR is not automatically support or resistance: higher-timeframe structure, premium/discount location and the retest reaction determine the working bias.

Identification and testing conditions

Step Mark Illustrative example Common mistake
1. First FVG Three-candle gap boundaries Bearish FVG 1.0820–1.0836 Including every wick
2. Opposing FVG Opposite imbalance Bullish FVG 1.0814–1.0832 Calling every overlap a BPR
3. Overlap Intersection of both boxes BPR 1.0820–1.0832 Drawing an untraceable box
4. Context Premium/discount and HTF swing Bullish bias, BPR in discount Entering on touch alone
5. Invalidation Close through the full BPR or swing H1 close below 1.0820 No pre-defined failure point

A price- and time-labelled entry example

In a hypothetical teaching scenario, two FVGs formed an overlap from 1.0820 to 1.0832. Price returned to the overlap at 14:00 UTC, wicked to 1.0826 and closed the H1 candle above 1.0828. Instead of entering on the first touch, the example waits for confirmation: entry 1.08254, SL 1.08110 (14.4 pips or 1R), and an illustrative 2R target at 1.08542. This is a risk model, not a win-rate promise.

Check the hypothetical risk calculation

Input Value Calculation
Entry on a later pullback 1.08254 Illustrative input, not a fill
Stop 1.08110 0.00144 = 14.4 pips with pip size 0.0001
2R target 1.08542 1.08254 + 2 × 0.00144; excludes fees and slippage

When does a BPR fail?

  • An H1 candle closes fully outside the BPR and does not reclaim it.
  • The overlap is too thin for the spread or current session volatility.
  • The BPR conflicts with higher-timeframe bias and has no displacement confirmation.
  • Repeated retests consume the zone, so it is no longer fresh.

For related context, read Displacement in SMC, FVG vs IFVG and MSS in SMC.

Frequently asked questions

Is every BPR an entry zone?

No. It is a potential balance area. Bias, price reaction, invalidation and position risk still need separate rules.

Must both source FVGs remain fresh?

Track the state of each FVG. If one was already filled before the overlap appeared, confidence should be reduced and tested separately.

Editorial note: Học Làm Trader Editorial Team. Educational content only, not investment advice.

Worked example and limits

Direct answer: BPR is a practitioner label for an overlap or balance between two Fair Value Gaps. It is a descriptive hypothesis, not proof that price will reverse or that an overlap is tradable.

Failure cases include selecting the overlap after the move, changing the three-candle rule between samples, ignoring session/news, or treating every gap as institutional evidence. No trade is valid when the gap is stale or too wide, higher-timeframe context conflicts, spread consumes the risk budget or the data source is unsuitable. Link to the FVG guide, market structure, VSA, position sizing and risk management. Checked 16 September 2026.

3 thoughts on “BPR in ICT: Finding Balance Between Two Fair Value Gaps”

  1. Pingback: Fair Value Gaps: Identification, Validation And Failure

  2. Pingback: Breaker Blocks: Formation, Validation And Failure

  3. Pingback: ICT Power Of Three: Accumulation, Manipulation, Distribution

Leave a Reply

Your email address will not be published. Required fields are marked *